Page 5 of 8
Re: Emco Pc turn 50
Posted: Thu Dec 24, 2020 9:55 am
by Gordon1234
I have to index turret first (in instructions file) with M18. Will check m101 macro. I try T1D1 or T2D2, doesnt work. But I see you say t0101, its 01 not D1?
Re: Emco Pc turn 50
Posted: Thu Dec 24, 2020 10:32 am
by martyscncgarage
Follow the instructions for one input timer (assuming you are using this method)
To change tools T0101 to change to tool 1
T0202 to change to tool 2
Re: Emco Pc turn 50
Posted: Thu Dec 24, 2020 11:30 am
by martyscncgarage
Gordon, could you please post your most recent report?
Thanks,
Marty
Re: Emco Pc turn 50
Posted: Thu Dec 24, 2020 12:32 pm
by Gordon1234
Of course, will do that tomorrow. Don't have the full licence too, I have to buy one.
Re: Emco Pc turn 50
Posted: Thu Dec 24, 2020 12:34 pm
by martyscncgarage
Gordon1234 wrote: ↑Thu Dec 24, 2020 12:32 pm
Of course, will do that tomorrow. Don't have the full licence too, I have to buy one.
You don't need Pro or Digitizing to get things working.
I just want to try and find the time to load your report on my benchtest rig and see how you have things setup. See if anything is out of the ordinary.
You MUST follow the schematic exactly with regards to inputs and outputs.
You are running 4.50 correct?
Marty
Re: Emco Pc turn 50
Posted: Fri Dec 25, 2020 9:23 am
by Gordon1234
Hi and merry christmas Marty !
Here is report file. Wiring exact schematic input an output (Input 2 turretSyncbit and output 2 Rotateturret) Only 5V with relay in input 2, because not 24V.
Yes, it's 4.50.
Re: Emco Pc turn 50
Posted: Sun Dec 27, 2020 7:16 am
by Gordon1234
Hello !
Today, I uninstall cnc12 lathe (all files) and install it again. I follow exactly intructions file in time based turret, and m18 works ! But only 1 time.
I put m18 on MDI, output 2 activates, turret wait for input 2, and index itself in tool 1. I was so happy. But...
I try to call t0303, software says me I need Pro version to m107 ATC (I have to buy it for my job, but want setup all things before buy it), so in alt-i I activate output 2 (ctrl alt F) to move at other tool, and in MDI m18 doesn't work again (output 2 not activated).
So close...
Re: Emco Pc turn 50
Posted: Sun Dec 27, 2020 9:29 am
by martyscncgarage
Gordon1234 wrote: ↑Sun Dec 27, 2020 7:16 am
Hello !
Today, I uninstall cnc12 lathe (all files) and install it again. I follow exactly intructions file in time based turret, and m18 works ! But only 1 time.
I put m18 on MDI, output 2 activates, turret wait for input 2, and index itself in tool 1. I was so happy. But...
I try to call t0303, software says me I need Pro version to m107 ATC (I have to buy it for my job, but want setup all things before buy it), so in alt-i I activate output 2 (ctrl alt F) to move at other tool, and in MDI m18 doesn't work again (output 2 not activated).
So close...
Yes you need pro for ATC...sorry about that. Looks like you are ready for it though
Re: Emco Pc turn 50
Posted: Sun Dec 27, 2020 9:46 am
by Gordon1234
Yep I buy it. Just waiting for paypal email, and let's go !
Re: Emco Pc turn 50
Posted: Sun Dec 27, 2020 9:52 am
by martyscncgarage
Send me a FRESH report and I'll try and double check it. Weekends are busy for me and try and spend time with family for my "off" time