Page 15 of 15
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Tue Nov 05, 2024 11:46 am
by mgeyer
LSGreen wrote: ↑Sun Nov 03, 2024 9:10 pm
So far, and I'm not very far into v5.2 but when I turn on the wireless MPG the speakers on my computer start rapidly clicking. Haven't had this happen in prior versions.
Are you using wireless speakers? This sounds like you're experiencing some sort of interference between two wireless devices operating at the same frequency.
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Wed Nov 06, 2024 4:18 pm
by LSGreen
Nope, my speakers are wired. Thanks for the response.
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Wed Nov 06, 2024 7:01 pm
by grossmsj
FWIW, since I installed 5.18 my MPG will occasionally have very jumpy movements. If I spin the wheel the machine will sort of lurch along, and I see the DRO numbers on the MPG increment very slowly. When I restart the computer the problem disappears. It sort of looks like there is a very slow polling.
Have not gone through installation of 5.2
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Thu Nov 07, 2024 8:43 pm
by cnckeith
grossmsj wrote: ↑Wed Nov 06, 2024 7:01 pm
FWIW, since I installed 5.18 my MPG will occasionally have very jumpy movements. If I spin the wheel the machine will sort of lurch along, and I see the DRO numbers on the MPG increment very slowly. When I restart the computer the problem disappears. It sort of looks like there is a very slow polling.
Have not gone through installation of 5.2
maybe mpg is going bad? v5.18 and v5.20 is running hundreds of wmpg's with no complaints so i dont' think its a CNC12 thing you are experiencing.
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Thu Nov 07, 2024 8:44 pm
by cnckeith
LSGreen wrote: ↑Sun Nov 03, 2024 9:10 pm
So far, and I'm not very far into v5.2 but when I turn on the wireless MPG the speakers on my computer start rapidly clicking. Haven't had this happen in prior versions.
hmm well that is odd. there has been no changes on the wireless mpg that i can think of that would cause that.
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Fri Nov 08, 2024 9:26 pm
by LSGreen
cnckeith wrote: ↑Thu Nov 07, 2024 8:44 pm
LSGreen wrote: ↑Sun Nov 03, 2024 9:10 pm
So far, and I'm not very far into v5.2 but when I turn on the wireless MPG the speakers on my computer start rapidly clicking. Haven't had this happen in prior versions.
hmm well that is odd. there has been no changes on the wireless mpg that i can think of that would cause that.
Yea, I don't know. My MPG is new, only a few operations with it. Like I said, I Haven't experienced the noise with any lower versions. Maybe I will reinstall v5.20. Just For fun, see what happens.
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Tue Jan 14, 2025 1:04 pm
by biobrett
I don't know if this is the correct place to post this, but I have an issue with the "Job Run Options" -> "Search" function since updating to 5.22. The first time I use search (since starting CNC12), it works fine. The second time I happen to use it, it causes the application to crash (CNC12 exits). I'm wondering if anyone else has this issue and whether there is a fix?
Small update, I tried this in the "offline" version and experienced the same behavior.
bb
Re: 10-22-24 UPDATE! CNC12 v5.20 has been released Mill, Lathe, Router, Plasma is now available for public testing.
Posted: Tue Jan 14, 2025 1:22 pm
by ASPeters
biobrett wrote: ↑Tue Jan 14, 2025 1:04 pm
I don't know if this is the correct place to post this, but I have an issue with the "Job Run Options" -> "Search" function since updating to 5.22. The first time I use search (since starting CNC12), it works fine. The second time I happen to use it, it causes the application to crash (CNC12 exits). I'm wondering if anyone else has this issue and whether there is a fix?
Small update, I tried this in the "offline" version and experienced the same behavior.
bb
Please see this post:
https://centroidcncforum.com/viewtopic. ... 703#p94703
If you are experiencing similar behavior, it is fixed and will be part of the next beta/release.