I just purchased a new sync 45. I don't want to do something stupid. Are the arc transfer wires used? I understand the divided voltage (thc) and the torch on and off.
Thanks
Hypertherm sync 45 hook up question
-
cardin3
- Posts: 54
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Hypertherm sync 45 hook up question
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Centroid_Jacob
- Web Developer
- Posts: 100
- Joined: Wed Oct 19, 2022 4:49 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: Yes
- Allin1DC CNC Controller: No
- Hickory CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: No
- CNC11: Yes
- CPU10 or CPU7: No
- Location: Howard, PA
Re: Hypertherm sync 45 hook up question
I moved this post to the Plasma Forum.
When requesting support please read this post first.
A fresh report makes it easier to assist you. To make a report check this post
A fresh report makes it easier to assist you. To make a report check this post
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Joey
- Plasma/Laser Lead
- Posts: 674
- Joined: Tue Aug 17, 2021 10:51 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
The THC will act as your ARC OK/ ARC Transfer.
But Hypertherm Recommends using their ARC OK/ ARC Transfer For the most accurate Pierce delays.
I usually like to hook up Hypertherm's according to their recommendations.
But Hypertherm Recommends using their ARC OK/ ARC Transfer For the most accurate Pierce delays.
I usually like to hook up Hypertherm's according to their recommendations.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cardin3
- Posts: 54
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
I there a centroid wiring diagram? and any configuration requirements?
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Joey
- Plasma/Laser Lead
- Posts: 674
- Joined: Tue Aug 17, 2021 10:51 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
You can reference the Everlast arc okay connection.
https://www.centroidcnc.com/dealersuppo ... 195.r1.pdf
There's 2 arc transfer pins on the hypertherm cnc communication port. One will connect to Acorns Com. The other will connect to the Acorns Input
Pin 12 and 14 on the Hypertherm CNC Com ports are the ARC transfer pins.
Connect pin 12 to the Acorns Common.
Connect pin 14 to the Desired Acorn Input
Just assign the input as arc ok in the wizards input definition menu
https://www.centroidcnc.com/dealersuppo ... 195.r1.pdf
There's 2 arc transfer pins on the hypertherm cnc communication port. One will connect to Acorns Com. The other will connect to the Acorns Input
Pin 12 and 14 on the Hypertherm CNC Com ports are the ARC transfer pins.
Connect pin 12 to the Acorns Common.
Connect pin 14 to the Desired Acorn Input
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cardin3
- Posts: 54
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
Ok. Sounds good. Thanks for the reply. I will get it wired up and check back in.
Thanks
Thanks
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cardin3
- Posts: 54
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
One other question. Pin 13 on the powermax is a ground pin. Should I contact that to the ground on acorn.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Joey
- Plasma/Laser Lead
- Posts: 674
- Joined: Tue Aug 17, 2021 10:51 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
That should be connected to the shield on the Hypertherm CNC Com cable.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cardin3
- Posts: 54
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Hypertherm sync 45 hook up question
Ok. It's cutting!! Every thing seems fine.i have a question about book setting voltage VS actual voltage. I'll start a separate thread.
Again, thanks so much.
Mike
Again, thanks so much.
Mike
1 user liked this post
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)