I built a gang tool lathe some years back and it is dedicated to 4 jobs. The tooling setup never leaves the table.
I am sure that the updates are 4 or 5 versions old if not older. It works well for my needs so I leave it alone.
I powered up my system and turned on the remote and the screen is blank all but the battery level and signal strength indicator.
There is a little square that blinks when I rotate the MPG wheel, that is all I get.
I replaced the battery, I moved the antenna to other USB ports and restarted the system mutable times. Is it dead?
Wirerless Remote note working <install Pro License>
Moderator: cnckeith
Re: Wirerless Remote note working
In you report file, what is the value for Parameter 218?
On the F7/Utility -> F8/Options screen, what license level do you have active?
On the F7/Utility -> F8/Options screen, what license level do you have active?
-
- Posts: 218
- Joined: Fri Jul 27, 2018 5:42 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Wirerless Remote note working
I fund the issue. The wizard Is changing it's self back to NO MPG.
https://centroidcncforum.com/viewtopic.php?f=60&t=4508
https://centroidcncforum.com/viewtopic.php?f=60&t=4508
-
- Posts: 7554
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Wirerless Remote note working
that's because you need a Pro license file to use the Wireless MPG.TRM wrote: ↑Sun Jan 16, 2022 2:24 pm I fund the issue. The wizard Is changing it's self back to NO MPG.
https://centroidcncforum.com/viewtopic.php?f=60&t=4508
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 9915
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: Wirerless Remote note working
ALWAYS, ALWAYS, ALWAYS Post a fresh report when asking for help.
We can take a look at the settings and give you suggestions.
Marty
We can take a look at the settings and give you suggestions.
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ