Search found 11 matches
- Mon May 08, 2023 8:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
yes sir
- Mon May 08, 2023 11:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
Pinging 10.168.41.2 with 32 bytes of data: Reply from 10.168.41.2: bytes=32 time<1ms TTL=255 Reply from 10.168.41.2: bytes=32 time<1ms TTL=255 Reply from 10.168.41.2: bytes=32 time<1ms TTL=255 Reply from 10.168.41.2: bytes=32 time<1ms TTL=255 Ping statistics for 10.168.41.2: Packets: Sent = 4, Recei...
- Mon May 08, 2023 10:46 am
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
Hello Gentlemen. I have had some issues with this acorn. had a power supply kill my acorn board and my beagle bone board at same time. I bought all new. installed everything again and had it working good for a week. went to add a new stepper to the mix. Now cpu will not connect to acorn board. have ...
- Fri Mar 31, 2023 11:51 am
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
Ok update replaced Beagle bone as reported in last post. No go lights on acorn board were lit up but beagle bone were not lit. So i did some checking with volt meter and acorn board has something burnt on it no power to beagle bone. So Just in reading some of the post in here i replaced my acorn boa...
- Thu Sep 08, 2022 8:20 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
OK guys has been a while since i have done anything with this. Summer was very busy. Did some checking and found beagle bone green wasn't burnt up. Replaced that and put files on it.But cant get heart beat. Lights on Acorn board are lit up but no power to beagle bone green. Where do i look next. any...
- Wed Apr 27, 2022 8:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
ok guys I have acorn board lit up but no heart beat. had disconnected everything on board. then repowered with a new power supply that i ordered because i thought that was my proplem . only reason I thought that is because the board was blinking. didn't remove wires and test power supply. Learned a ...
- Tue Apr 26, 2022 9:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
sorry ive tried to do a report since software wants to connect to board and can't. won't let me open software completely .
- Tue Apr 26, 2022 9:31 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
Re: acorn board wont power up
I made it through set up .set it up on cl57 stepper ran back and forth. Just fine. went to run motor up a little faster and everything quit.
- Tue Apr 26, 2022 7:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn board wont power up
- Replies: 19
- Views: 2752
acorn board wont power up
Hello guys. My acorn board will not power up. I plug my power supply in and the board tries to power up but sits there and lights up ,shuts down, lights up, shuts down. I was in the stages of setting up stepper motor when it quit. thought it was power supply but it was not. Now im sick to my stomach.
- Sun Jan 30, 2022 8:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Fuji servo drives with acorn.
- Replies: 23
- Views: 2141
Re: Fuji servo drives with acorn.
model is fuji RYH 401 F5-vv2 with GYS 401-d5-rc2 servo motor. Thank you for the reply.