Search found 525 matches

by Joey
Sat Jun 01, 2024 2:39 pm
Forum: Acorn CNC Plasma
Topic: THC problem
Replies: 2
Views: 40

Re: THC problem

Your making progress. The purple is the THC anti dive. This is controlled by the Anti Dive Hysteresis in the THC config. If the voltage rises more than 7 percent of the target voltage then anti dive will kick in. Default settings is 7 percent o believe I would increase the anti dive from the stock 7...
by Joey
Mon May 27, 2024 4:32 pm
Forum: Acorn CNC Plasma
Topic: Torch calibration program
Replies: 1
Views: 123

Re: Torch calibration program

Torch Calibration is in the "Utils" button on the bottom of the VCP.
by Joey
Sun May 26, 2024 9:34 am
Forum: Acorn CNC Plasma
Topic: Acorn Plasma THC Controller as router
Replies: 2
Views: 101

Re: Acorn Plasma THC Controller as router

Yes

When installing CNC12 you will see an option for a Router/ Plasma combination.

The installer will download both Router and Plasma versions with a Desktop swap button for jumping from the plasma to router software.
by Joey
Wed May 22, 2024 2:46 pm
Forum: Acorn CNC Plasma
Topic: SHEET CAM
Replies: 15
Views: 4008

Re: SHEET CAM

There is a video link in my Post found here https://centroidcncforum.com/viewtopic. ... eed#p67483
by Joey
Thu May 16, 2024 3:24 pm
Forum: Acorn CNC Plasma
Topic: Turns/inch motor shaft
Replies: 5
Views: 363

Re: Turns/inch motor shaft

Thanks for pointing this out Guys, Pg.3 and 9 of the Plasma Manual has been updated.

You can find the Updated manual here
https://www.centroidcnc.com/centroid_di ... manual.pdf
by Joey
Tue May 07, 2024 5:37 pm
Forum: Centroid Acorn CNC Controller
Topic: Machine parameter for Linear encoder input
Replies: 11
Views: 701

Re: Machine parameter for Linear encoder input

The AIKRON Model:AKM1 Has been Tested at Centroid. The Signal Type Needs to be the 5v RS422 https://www.aikrondro.com/product/aikron-akm-series-linear-encoders/ I've attached a snip of the DB9 connector of the Aikron and the Changes needed to match the Centroid DB9 Encoder Port. Aikron Scale Wiring....
by Joey
Tue May 07, 2024 4:47 pm
Forum: Acorn CNC Plasma
Topic: SheetCam Hypertherm 45XP .tool file (inch)
Replies: 1
Views: 200

Re: SheetCam Hypertherm 45XP .tool file (inch)

Acorn Plasma Takes care of any ''Tool'' settings. Acorn Plasma comes with all default Profiles from Hypertherm.
Acorn Plasma does not use any of the tool information from Sheetcam .

Sheetcam Has a forum if you really want the Sheetcam toolset.
by Joey
Fri May 03, 2024 11:21 am
Forum: Acorn CNC Plasma
Topic: Please help! I fried my THC!!!
Replies: 11
Views: 1534

Re: Please help! I fried my THC!!!

Thats odd. Can you post a fresh report Please. The Report will have all you settings and macros. So I can then really see what the control is doing and why. Can you also Post the G-code used. I'm thinking the M61 macro is at fault of there is something going on in the G-code. Was the G-code job from...
by Joey
Wed May 01, 2024 5:50 pm
Forum: Acorn CNC Plasma
Topic: Please help! I fried my THC!!!
Replies: 11
Views: 1534

Re: Please help! I fried my THC!!!

Good choice on switching to the Everlast Torch Touch with Everlast and Primeweld is not officially supported by Centroid. I haven't seen another Everlast Using the TX torch touch yet. What does the Tin Wire connect too? I have seen the Primeweld Hooked up to the TX boards Torch touch and it seems to...
by Joey
Wed May 01, 2024 4:09 pm
Forum: Acorn CNC Plasma
Topic: Speed around corners
Replies: 6
Views: 828

Re: Speed around corners

Lowering the Parameter P223 should help with Arcs. I wouldn't take P223 below 100. Setting the Drives to 6400 and the wizard to match should also fix the speed up issue. The Laser offset issue is puzzling. I've even loaded your report on a fresh 5.08 build and Laser set X/Y functioned as expected. I...