I like the idea of updating
Looking at getting another machine as a backup for this product, then I would be more comfortable with updating
I have reached out to Tech Support and they are going to look and see if they can help.
If they can and the price is reasonable, I will have them do it.
Thanks
Search found 59 matches
- Fri Nov 10, 2023 2:21 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Outputs acting strange
- Replies: 8
- Views: 1007
- Thu Nov 09, 2023 9:46 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Outputs acting strange
- Replies: 8
- Views: 1007
Re: Outputs acting strange
SO you are suggesting I replace the existing PLC program with standard new one? Not sure why I would/should do that instead of modifying the existing unless its hard to do? I hate doing anything more than necessary because in my experience it always causes more problems I run a one man shop/business...
- Thu Nov 09, 2023 5:05 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Outputs acting strange
- Replies: 8
- Views: 1007
Re: Outputs acting strange
Ok I did use the Alt-i and it/they are showing true/false when commanded I am only looking for an ON/OFF contact The VFD has its own power 5v and needs 2 leads to be sealed/latched on to run Relay 9 N.O. held closed with M code As of now, Relay 9 will operate with the Aux3 Key & led light Need a...
- Wed Nov 08, 2023 11:23 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Outputs acting strange
- Replies: 8
- Views: 1007
Re: Outputs acting strange
I am using wires tightened in properly When I check Output relay 9 using the Aux 3 key I get a definite On/Off state Same wires placed in 4 or 6 is where I get inconsistent readings. Who do I need to contact to make PLC changes to get the Output 9 relay working with an M code command? Don't mind pay...
- Wed Nov 08, 2023 12:44 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Outputs acting strange
- Replies: 8
- Views: 1007
Outputs acting strange
I had posted earlier about Aux contact M code mapping After reviewing some videos and checking Outputs 4 & 6 I can NOT get any consistency from the state of contacts. I don't use Output 6 "Clamp" so I tested M10 and M11and I am NOT getting a definitive ON or OFF? I have connected 2 wir...
- Tue Nov 07, 2023 4:30 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Aux Contact output mapping to M Code
- Replies: 1
- Views: 775
Re: Aux Contact output mapping to M Code
I did some research and found the YouTube videos of PLC programing.
I believe I have it figured out.
Thanks
I believe I have it figured out.
Thanks
- Mon Nov 06, 2023 5:24 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Aux Contact output mapping to M Code
- Replies: 1
- Views: 775
Aux Contact output mapping to M Code
I am adding a function to my mill and would like to use the Aux9 output contactor, calling it up with an M Code in program (Both ON & OFF)? Aux9 output is currently actuated by Aux3 Key. This was used for a spindle brake pneumatic solenoid long before I acquired it (Don't need or use). Not sure ...
- Sun Dec 18, 2022 3:31 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error Codes 417 & 421
- Replies: 4
- Views: 658
Re: Error Codes 417 & 421
Ok Thanks
That makes sense
I will try changing the number
O's are in most of my programs because my Fanuc controls require it
That makes sense
I will try changing the number
O's are in most of my programs because my Fanuc controls require it
- Sun Dec 18, 2022 9:56 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error Codes 417 & 421
- Replies: 4
- Views: 658
Re: Error Codes 417 & 421
Ok
Then it could be in the middle of the program?
Will not run graph either
Then it could be in the middle of the program?
Will not run graph either
- Sat Dec 17, 2022 11:44 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error Codes 417 & 421
- Replies: 4
- Views: 658
Error Codes 417 & 421
I am getting an MPG encoder error, but everything seems to work fine. Also have a program that will not run "Abnormal End of Job"? Checked other programs and they have the same end to the program. Attached program 3333 is the one that gives error and 3336 runs fine. These are both engravin...