Search found 132 matches
- Fri Mar 08, 2024 10:27 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Jog Speeds after Update to CNC12 V5.08
- Replies: 3
- Views: 322
Re: Jog Speeds after Update to CNC12 V5.08
The feed rate and rapid rate are separate now. Dialing back the rapid rate will affect your jog speed.
- Tue Feb 27, 2024 11:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC Depot Spindle with Acorn and Hitachi WJ200
- Replies: 12
- Views: 821
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
I have an S30c and wanted to setup SV feature. I will have to try this out.
Bill
Bill
- Tue Feb 27, 2024 5:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 v5.08 ATC wizard issue
- Replies: 7
- Views: 477
Re: CNC12 v5.08 ATC wizard issue
Hi Keith,
Yes, I know that. It is off.
Bill
Yes, I know that. It is off.
Bill
- Tue Feb 27, 2024 5:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 v5.08 ATC wizard issue
- Replies: 7
- Views: 477
- Tue Feb 27, 2024 2:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 v5.08 ATC wizard issue
- Replies: 7
- Views: 477
Re: CNC12 v5.08 ATC wizard issue
Hello Chris, So setting it under the CNC control preferences page seems to work. It stays as yes in the ATC page to doing it that way. What about the slow/fast jog button not working? When I press it, I get no led on the button, yet in the message area it says slow jog selected but it stays in fast ...
- Tue Feb 27, 2024 12:17 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 v5.08 ATC wizard issue
- Replies: 7
- Views: 477
CNC12 v5.08 ATC wizard issue
Hello, Did a fresh install today of 5.08 Everything is setup and seems to be working fine except for an issue that I discovered. I setup my ATC through the wizard, however I have to edit the Mfunc6 macro to include an M66 and M62 at the beginning of the tool change and an M86 and M82 toward the end ...
- Wed Feb 21, 2024 11:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Adding functionality to VCP
- Replies: 1
- Views: 162
Adding functionality to VCP
Hello, I just added an Ether1616 to my setup. All is working good. Now that I have plenty of outputs to use I want to play a little. These machines are like hot rods, they are never done. My router has a 5 x 8 vacuum table that has 5 zones. What I would like to do for fun and functionality is add an...
- Fri Feb 09, 2024 7:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Software Feature Request: spindle speed adjustment
- Replies: 6
- Views: 501
Re: Software Feature Request: spindle speed adjustment
Yes, true.
Didn't think about that.
Didn't think about that.
- Thu Feb 08, 2024 5:18 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Software Feature Request: spindle speed adjustment
- Replies: 6
- Views: 501
Software Feature Request: spindle speed adjustment
Hello,
sometimes I manually adjust spindle rpm while a job is running. I find that the + - rate at which it adjusts the rpm is very quick.
It would be nice to be able to adjust the rate at which these buttons work. Sometimes just a tap will be too much, a slower rate would be nice.
Any thoughts?
Bill
sometimes I manually adjust spindle rpm while a job is running. I find that the + - rate at which it adjusts the rpm is very quick.
It would be nice to be able to adjust the rate at which these buttons work. Sometimes just a tap will be too much, a slower rate would be nice.
Any thoughts?
Bill
- Fri Jan 26, 2024 2:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Clearpath and C86ACCP question.
- Replies: 8
- Views: 1036
Re: Clearpath and C86ACCP question.
Ok, yes. I was wondering about that. I will do that.Your commons should all be tied together.
Thank you
Bill