Search found 86 matches
- Sun Nov 05, 2023 11:06 am
- Forum: Centroid Acorn CNC Controller
- Topic: Dynamic break wiring
- Replies: 0
- Views: 5991
Dynamic break wiring
God Morning to everybody. Out of all you fine individuals there has to be some one that could answer this question. I have this Board that came out of the Original build of the machine. Mazak QT8. I have the wiring diagram. I have the 120 Volts hooked up and the motor wires. From what I am seeing I ...
- Wed Nov 01, 2023 1:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: W9 Value
- Replies: 4
- Views: 503
Re: W9 Value
I’ll give it a try
Thank you
Thank you
- Wed Nov 01, 2023 1:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: W9 Value
- Replies: 4
- Views: 503
Re: W9 Value
ok I was told that there is a parameter you can change to get to the old ALT I display. Anybody Know what that might be.
- Wed Nov 01, 2023 12:50 pm
- Forum: Centroid Acorn CNC Controller
- Topic: W9 Value
- Replies: 4
- Views: 503
W9 Value
Hi to all does this make any sense? (You can view the value of W9 on the first page of the Alt-i display)
Thanks John
Thanks John
- Fri Sep 08, 2023 1:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Mazak QT8
- Replies: 0
- Views: 11954
Mazak QT8
Hello to all my question is. Is there anybody in this forum that has retrofitted a mazak QT8. Things are going very well. I’m working on the turret at this time. Anybody out there know anything about the turret. I did change all the proximity sensors to NPN. I set up some relays to run the index mot...
- Sat Jul 22, 2023 6:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe rapid to work then will not feed < look up, G98/G99>
- Replies: 4
- Views: 461
Re: Lathe rapid to work then will not feed
Yes that’s what it took was to put a G98 in the line
Thanks John
Thanks John
- Wed Jul 19, 2023 9:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe rapid to work then will not feed < look up, G98/G99>
- Replies: 4
- Views: 461
Lathe rapid to work then will not feed < look up, G98/G99>
Hi Guys I am just doing some testing on a mazak QT8 that I am retrofitting. I wrote a small program and it Rapids up to the work and then just sits there does not feed. Also says I Think it said 302 moving but it is not. I am including a report and my program. It must be something in the set up??? T...
- Sat Apr 08, 2023 4:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: corrupt files
- Replies: 5
- Views: 583
Re: corrupt files
Fixed I looked up the error code 0x80070570 and found some one that stated to go to C drive click on properties go to tools and scan the c drive came up needed repair let it do the repair and all good to go.
- Sat Apr 08, 2023 4:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: corrupt files
- Replies: 5
- Views: 583
Re: corrupt files
If I write an intercon program it will load. If I try to bring anything else in it says it is corrupt. I do not Know where the intercon program is going
- Sat Apr 08, 2023 3:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: corrupt files
- Replies: 5
- Views: 583
Re: corrupt files
It shows the folder is in there, and that it is corrupt and it will not let me delete it. To Replace it. Kinda Sucks