Today I test with timer (found schematic, instruction file). Wiring, setting parameters. When in MDI I put "m18" (turret indexing), I have a message "Waiting for memory #51 (M101). Output 2 (turret rotate) not activated.
What is it ?
Search found 45 matches
- Wed Dec 23, 2020 4:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
- Tue Dec 22, 2020 5:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
No worries, you are so helpful !
I will try time based turret, using ToolSyncbit at toolhome, and don't use second sensor. I think it will be easier, schematic is the same (I will use acorn input), and in instructions files, I have to put time in ms.
Hope I can try that tomorrow !
I will try time based turret, using ToolSyncbit at toolhome, and don't use second sensor. I think it will be easier, schematic is the same (I will use acorn input), and in instructions files, I have to put time in ms.
Hope I can try that tomorrow !
- Tue Dec 22, 2020 3:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
No problem marty don't apologize. Yes, both relays turn on and off, input 3 get green when Tool 1 is in position (turret sync bit), but input 4 stay red (tool position bit 1 or turret tool counter). It's the same problem without relays. I will connect to acorn input terminal relays. Maybe set the tu...
- Tue Dec 22, 2020 1:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
Hi Marty. I use the schematic for emco pc55, and instructions in file, but instructions file says about 4 bits sensors on E point, so what I have to do with these following points E, F, G, H on 1st page of instructions ? Yes, with Ali+i, and ctrl alt F on output 2, Turret rotates, and relays opening...
- Mon Dec 21, 2020 1:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
Yes with diagnostic scrren on alt i. Yes, NO output like you said.
Here is a picture of wiring, I use power source of acorn (24V ansd 5V)
Here is a picture of wiring, I use power source of acorn (24V ansd 5V)
- Sun Dec 20, 2020 7:39 am
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
Hello ! Some news today. Wire done, no problems. Input 3 green for tool 1 (tool sync) it's ok, but input 4 (tool position) never green (always red), but relay works fine with sensor for each tool. Maybe a parameter in wizard ? (tested with "tool counter" and "tool position bit 1")
- Mon Dec 14, 2020 1:49 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
Thank you, today was spindle setup for my milling machine (ac servo), tomorrow the lathe !
- Sun Dec 13, 2020 3:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
Ok, so 5V/com on DC+ and DC-, sensor output on input relay board, ok for jumper, and there is NC, COM and NO on the other side, so relay COM to power supply COM, and output NC or NO to acorn input. I'm good ?
- Sun Dec 13, 2020 1:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
Ok will try this today or tomorrow
- Sun Dec 13, 2020 11:23 am
- Forum: Centroid Acorn CNC Controller
- Topic: Emco Pc turn 50
- Replies: 76
- Views: 26837
Re: Emco Pc turn 50
No problems marty
No relays not wired, because I d'ont know how wiring them. Wich one goes to DC+ and DC- ? IN goes to acorn input ?
No relays not wired, because I d'ont know how wiring them. Wich one goes to DC+ and DC- ? IN goes to acorn input ?