Search found 2301 matches
- Sun Jun 02, 2024 5:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ethernet Communication Error, Bulletin270 followed, still there SOLVED (again...?)
- Replies: 15
- Views: 202
Re: Ethernet Communication Error, Bulletin270 followed, still there SOLVED (again...?)
I'm in the same boat as Uwe, I have one machine with and Intel NIC and my other machine is Realtek. Both perform flawlessly when setup correctly.
- Sun Jun 02, 2024 1:32 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ethernet Communication Error, Bulletin270 followed, still there SOLVED (again...?)
- Replies: 15
- Views: 202
Re: Ethernet Communication Error, Bulletin270 followed, still there NOT SOLVED
Does you CNC PC have an Intel network card? If so, did you check to see if it's set correctly?
- Sun Jun 02, 2024 10:20 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 Router Restructure Beta Software thread.
- Replies: 7
- Views: 469
Re: CNC12 Router Restructure Beta Software thread.
I start this thread as a place to include you our valued customers in the continued development of CNC12 Router. Hi Keith, would it be possible in the future to add the ability to control a drill block on a CNC router using a wizard page? Like the rack mount ATC setup where you tell CNC12 the tool ...
- Sun Jun 02, 2024 8:35 am
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 383
Re: No signal from Acorn to the stepper drivers
Does that apply to most of this kind of stepper drives? I am using Stepperonline CL86T-Drives, which should be very similar to the leadshine and i have set the frequency to 200kHz, too. In the manual the max Pulse Input Frequency is 200kHz, so i thougt i should use this for Acorns Setup, too? My st...
- Sat Jun 01, 2024 8:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 383
Re: No signal from Acorn to the stepper drivers
You of course can wire and program the machine any way you like but if you want it to work correctly wire the drives to 5V and the DB25 as per the Leadshine manual. Stepper drives wire to the DB25 and servo drives wire to the Acorn headers. It clearly starts this in the Acorn install manual and coun...
- Fri May 31, 2024 6:53 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Grizzly G0619 Z Axis lag - Loosing position <resolved>
- Replies: 14
- Views: 817
Re: Z Axis lag - Loosing position
Well all appears to be fixed by going to the 5v logic side via the DB25 connector. Thanks for all the help. My other major take a way was to stop using E-stop, and only use that if abs necessary. It looks like the drivers need a moment after enable to be able to receive commands. So feed hold when ...
- Fri May 31, 2024 5:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 383
Re: No signal from Acorn to the stepper drivers
I'd also set the steps/rev on the drives to 3200 and set the step rate to 100,000 in the wizard.
This Leadshine page has a link to the manual. https://www.leadshine.com/product-detail/ES-DH2306.html
This Leadshine page has a link to the manual. https://www.leadshine.com/product-detail/ES-DH2306.html
- Fri May 31, 2024 5:18 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 383
- Thu May 30, 2024 9:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 383
Re: No signal from Acorn to the stepper drivers
Look again at your error log, you don't have perfect communication between the PC and Acorn. Your error log has several communication errors, MPU resends and PC resends. As Ken stated, share some pics and other info so others can better help you. Please start a Google photo album and share the link ...
- Thu May 30, 2024 4:38 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Centroid Oak with Rexroth IndraDrive M servo drives
- Replies: 6
- Views: 371
Re: Centroid Oak with Rexroth IndraDrive M servo drives
Thanks again for the info. I have many manuals that I downloaded from Rexroth and there's a lot of info out there. After further digging into the machine it appears that these Rexroth drives use Sercos which is a fiber optic connection to the controller which is a PCI card inside the PC on the machi...