Search found 7466 matches
- Mon Jun 03, 2024 8:39 am
- Forum: Centroid Acorn CNC Controller
- Topic: New Topic and CNC a Pen out of Wood/Metal
- Replies: 2
- Views: 68
Re: New Topic and CNC a Pen out of Wood/Metal
most use a cad cam system to create these kind of cnc lathe part g code programs.
- Mon Jun 03, 2024 8:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: CHIPS (CNC12 Highly Intuitive Probing System). The must have Add-On for CNC12
- Replies: 4
- Views: 96
- Fri May 31, 2024 4:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 378
Re: No signal from Acorn to the stepper drivers
these drives should probably be connected to the DB25
do you have link to the manual for these drives?
do you have link to the manual for these drives?
- Fri May 31, 2024 4:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Replacement Ethernet components
- Replies: 5
- Views: 205
Re: Replacement Ethernet components
I’d say your electrician owes you a new acorn system. The switch is maybe $20 the cost of the ether1616 board, I can understand them not wanting to break up prebuilt kits. I know it is a pain, but I’d say you need to buy an entirely new kit. The risk is that you fry each additional component you ad...
- Fri May 31, 2024 4:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Replacement Ethernet components
- Replies: 5
- Views: 205
Re: Replacement Ethernet components
flashing (aka debricking, aka bootloader) instructions are on the Acorn start here page.
https://www.centroidcnc.com/centroid_di ... guide.html
https://www.centroidcnc.com/centroid_di ... guide.html
- Fri May 31, 2024 4:20 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Replacement Ethernet components
- Replies: 5
- Views: 205
Re: Replacement Ethernet components
the glue is there to stop you from plugging anything into it.
- Fri May 31, 2024 3:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 54
- Views: 1566
Re: Rough Motion on Circular Toolpaths
remind me did these drives have drive tuning software?
and you could try messing with delta v max but, you might be going down a rabbit hole with that one.
https://centroidcncforum.com/viewtopic. ... 707#p82707
and you could try messing with delta v max but, you might be going down a rabbit hole with that one.
https://centroidcncforum.com/viewtopic. ... 707#p82707
- Fri May 31, 2024 3:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 54
- Views: 1566
Re: Rough Motion on Circular Toolpaths
trying a different pc is just a basic debug technique to quickly eliminate the PC as a possible source of an issue. i carry spare $150 PC's with me just for this purpose, that way i don't have to spend hours/days working on someone else's PC to try and solve an issue. :-) its probably not the PC BUT...
- Fri May 31, 2024 10:10 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Cycle Start programmatically
- Replies: 3
- Views: 166
- Fri May 31, 2024 10:00 am
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 18
- Views: 378
Re: No signal from Acorn to the stepper drivers
- Run the PC Tuner on the PC , and then run the stress test.
https://www.centroidcnc.com/centroid_di ... loads.html
- and make a photo album with the requested info so we can help you out.
https://www.centroidcnc.com/centroid_di ... loads.html
- and make a photo album with the requested info so we can help you out.