One wheel with a flange and one without. This reduces friction and belt wear.
Tom
Search found 3171 matches
- Thu Nov 02, 2017 12:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Logan lathe CNC conversion
- Replies: 79
- Views: 26754
- Fri Oct 27, 2017 4:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: encoder suitability
- Replies: 59
- Views: 21516
Re: encoder suitability
It was around $650 for a 776-B-S-1024-R-HV-E-9D-A-Y-N
- Fri Oct 27, 2017 1:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: encoder suitability
- Replies: 59
- Views: 21516
Re: encoder suitability
Encoder Products Company has big-bore encoders (up to 1.875") that work great on spindles.
http://encoder.com/products/incremental ... model-776/
Cheers,
Tom
Cheers,
Tom
- Tue Oct 17, 2017 11:38 am
- Forum: Centroid Acorn CNC Controller
- Topic: Limit/home switches
- Replies: 15
- Views: 6646
Re: Limit/home switches
Scott, I have a lot of users that run into the same problem with the start button as you do. I've created a --NULL--.CNC file that does not contain anything. I ask that the users load that program when they are done running theirs. That way is someone is using the machine in manual mode and they ina...
- Fri Sep 29, 2017 12:54 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Oak vs MPU11/GPIO4D
- Replies: 5
- Views: 2611
Re: Oak vs MPU11/GPIO4D
Oak also has an analog input if you want to do a spindle load meter. MPU11/GPIO4D needs an expansion board.
- Tue Sep 26, 2017 3:03 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error in RT-200 Manual wiring diagram?
- Replies: 1
- Views: 1181
Error in RT-200 Manual wiring diagram?
Page 32 (DC wiring) in the RT-200 manual shows Encoder common (blk/red) connected to pin D of the Amphenol connector. The home switch green wire is also connected to pin D on the Amphenol connector. Is this correct?
- Tue Sep 26, 2017 2:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Motor compatible with ALLIN1DC?
- Replies: 2
- Views: 1251
Re: Motor compatible with ALLIN1DC?
Thanks, Scott. This will be a DC1 addition and I didn't know the DC1 could run at a different bus voltage. Everything else will be at 155V (rectified 115V) without a transformer. I'll probably change out the motor since I really don't want to add a transformer and the encoder is only 1000L so I'd ha...
- Mon Sep 25, 2017 12:22 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Motor compatible with ALLIN1DC?
- Replies: 2
- Views: 1251
Motor compatible with ALLIN1DC?
I have a rotary table with and old DC brushed K&D MagMotor. I contacted the manufacturer and the only specs available are: Ke ~ 28.3 volts/1000 rpm Kt ~ 38.3 oz-in/amp Rt ~ 0.90 ohms Attached is a photo of the motor nameplate. I was hoping this would work with my ALLIN1DC control. Liviu or Keith...
- Sat Sep 09, 2017 8:28 pm
- Forum: Success Stories
- Topic: A Small Life Preserver
- Replies: 1
- Views: 2410
Re: A Small Life Preserver
Rick,
Since it's steel, just write on it with a Sharpie and then wipe it off with a little acetone and write your next message.
Tom
Since it's steel, just write on it with a Sharpie and then wipe it off with a little acetone and write your next message.
Tom
- Sat Sep 09, 2017 8:22 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Anamet Anaconda MTC Conduit <<Answered>>
- Replies: 3
- Views: 1804
Re: Anamet Anaconda MTC Conduit
Thanks, Liviu and Marty. I was looking for 3/4" Anaconda not the 1.25" console extension and I did find a place that will sell by the foot. West Side Electric Supply in South Elgin, Illinois has all the sizes sells cut lengths. For anyone who is building a CNC machine, Anamet Anaconda M.T....