I’m a little confused. I did go into the .hom file and setup code
To find the zero mark on the motor encoder for accurate homing. So I’m not scared to play in one of these files if you care to elaborate and dumb it down just a little I’ll make it happen.
Search found 218 matches
- Mon Mar 11, 2019 9:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help first part
- Replies: 11
- Views: 5203
- Mon Mar 11, 2019 7:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help first part
- Replies: 11
- Views: 5203
Re: Help first part
Yes Intercon
- Mon Mar 11, 2019 5:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help first part
- Replies: 11
- Views: 5203
Re: Help first part
Thanks for the help guys. It was the limit settings that need adjusting. Got another thing that needs adjusting. This is a gang lathe. It stops after each tool is finished and ask for the next tool. I press cycle start and it uses the next tool and when it's done it ask for the next tool again. I wa...
- Mon Mar 11, 2019 12:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help first part
- Replies: 11
- Views: 5203
Re: Help first part
It shows the tool path but I have not run simulation. Should I?
- Mon Mar 11, 2019 10:57 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help first part
- Replies: 11
- Views: 5203
- Sun Mar 10, 2019 3:36 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help first part
- Replies: 11
- Views: 5203
Help first part
I push cycle start it pulles in the contactor for flood add starts the spindle and stops. Tool 3 is a groove/turn and parting tool Tool 6 is a countersink to beburr the id of the part. I setup the tools as instructed in this video. https://www.youtube.com/watch?v=4Ik3gFMh8kU&t=1321s Video of wha...
- Mon Feb 04, 2019 3:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD Drive ready/reset
- Replies: 5
- Views: 2109
Re: VFD Drive ready/reset
The Spindle OK wire is going to IN5. I'm guessing it's looking for com for OK?
Do I need to configure IN5 for this. I have my X & Z zero marker signals on IN6 and 7 that why I ask?
Do I need to configure IN5 for this. I have my X & Z zero marker signals on IN6 and 7 that why I ask?
- Sun Feb 03, 2019 1:40 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD Drive ready/reset
- Replies: 5
- Views: 2109
Re: VFD Drive ready/reset
Thanks Gary.
- Sun Feb 03, 2019 12:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD Drive ready/reset
- Replies: 5
- Views: 2109
VFD Drive ready/reset
I'm almost ready to make chips! I have a Hitachi WJ200 VFD that I have all setup except for the drive ready signal to Acorn and the drive reset.
I have the drive all setup to do this I just need to hook it to Acorn. Can Acorn take a drive ready signal and can it reset the drive?
I have the drive all setup to do this I just need to hook it to Acorn. Can Acorn take a drive ready signal and can it reset the drive?
- Mon Jan 28, 2019 9:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Encoder mounting and runout interesting find
- Replies: 6
- Views: 2530
Re: Encoder mounting and runout interesting find
I bought a good one.
https://www.automationdirect.com/adc/sh ... -sh2500-vd
The Omron Ebay special was tempting but I chose the AD brand
https://www.automationdirect.com/adc/sh ... -sh2500-vd
The Omron Ebay special was tempting but I chose the AD brand